Shanghai Suote Valve Co.,Ltd. provides a large number of products each year, and has strong research and development capabilities, and the cycle time required for the product from design to finished product is short. The use of the technology contributes to the perfect manufacturing of SHSUOTE.DN80 Solenoid Control Valve with EMS Certification is widely used in the field(s) of Control Valve and the like. At present, Shanghai Suote Valve Co.,Ltd. are still a growing enterprise with a strong ambition to become one of the most competitive enterprises in the market. We will continue to research and develop new technologies for the birth of new products. Also, we will grasp the precious tide of opening up and reform to attract customers all over the world.
Product Description
DN80 Solenoid control valve with EMS certification 01. Description Solenoid Control Valve is an on-off control valve that either opens or closes upon receiving an electrical signal to the solenoid pilot control. This valve consists of a main valve and a two-way solenoid valve that alternately applies pressure to or relieves pressure from the diaphragm chamber of the main valve. It is furnished either normally open (de-energized solenoid to open) or normally closed (energized solenoid to open). Industrial uses for the solenoid control valve are many and include accurate control of process water for batching, mixing, washing, blending or other on-off type uses. Liquid level control can be provided by using a float switch or electrode probe which sends an electrical signal to open or close the valve as needed.02.Main parts&material| No. | Part | Material | China stardard |
| 1 | body | ductile iron | QT450-10 |
| 2 | bonnet | ductile iron | QT450-10 |
| 3 | Seat ring | stainless steel | ZG1Cr18Ni9 |
| 4 | Yoke | ductile iron | QT450-10 |
| 5 | Stem | stainless steel | 20Cr13 |
| 6 | Spring | stainless steel | 1Cr18Ni9 |
| 7 | Diaphragm | rubber | NBR+Reinforced nylon |
| 8 | Ball seat | rubber | NBR |
| 9 | Pipe fitting | brass/stainless steel | HPb59-1/0Cr18Ni9 |
| 10 | Pilot pressure reducing valve | brass | HPb59-1 |
001.Hydraulic control, no external driving force.
002.The main valve has only one moving part and the failure rate is low.
003.Diaphragm structure, no friction, high control sensitivity.
004.The pressure behind the valve does not change with the change of the pressure in front of the valve.
005.The pressure behind the valve does not change with the change of system flow;
006.Good static pressure reduction effect;
007.Wide range of pressure regulation after valve;
04.Dimensions| DN | L | ØD | ØK | H | N-Ød | ØB |
| PN10 | PN16 | PN25 | PN10 | PN16 | PN25 | PN10 | PN16 | PN25 | PN10 | PN16 | PN25 |
| 50 | 230 | 165 | 165 | 165 | 125 | 125 | 125 | 177 | 4-Ø19 | 4-019 | 4-019 | Ø99 | Ø99 | Ø99 |
| 65 | 290 | 185 | 185 | 185 | 145 | 145 | 145 | 202 | 4-Ø19 | 4-019 | 8-019 | Ø118 | Ø118 | Ø118 |
| 80 | 310 | 200 | 200 | 200 | 160 | 160 | 160 | 219 | 8-Ø19 | 8-Ø19 | 8-019 | Ø132 | Ø132 | Ø132 |
| 100 | 350 | 220 | 220 | 235 | 180 | 180 | 190 | 243 | 8-Ø19 | 8-Ø19 | 8-Ø23 | Ø156 | Ø156 | Ø156 |
| 125 | 400 | 250 | 250 | 270 | 210 | 210 | 220 | 243 | 8-Ø19 | 8-Ø19 | 8-Ø28 | Ø156 | Ø156 | Ø156 |
| 150 | 480 | 285 | 285 | 300 | 240 | 240 | 250 | 333 | 8-Ø23 | 8-Ø23 | 8-Ø28 | Ø211 | Ø211 | Ø211 |
| 200 | 600 | 340 | 340 | 360 | 295 | 295 | 310 | 428 | 8-Ø23 | 12-Ø23 | 12-Ø28 | Ø266 | Ø266 | Ø274 |
| 250 | 730 | 405 | 405 | 425 | 350 | 355 | 370 | 478 | 12-Ø23 | 12-Ø28 | 12-Ø31 | Ø319 | Ø319 | Ø330 |
| 300 | 850 | 460 | 460 | 485 | 400 | 410 | 430 | 538 | 12-Ø23 | 12-Ø28 | 16-Ø31 | Ø370 | Ø370 | Ø389 |
| *350 | 980 | 520 | 520 | 555 | 460 | 470 | 490 | 550 | 16-Ø23 | 16-Ø28 | 16-Ø34 | Ø429 | Ø429 | Ø448 |
NOTE:
1. *DN 125/350 use same internal as DN100/300
2. AISI 304 factory standard material, consult factory for AISI 316 material |
|
|
|
| Design standard | CJ/T219, JB/T10674 |
| Connection standard | GB/T17241.6 |
| Face spacing standard | GB/T12221 |
| Inspection testing standard | GB/T13927 |
| Nominal diameter | DN50~DN600(2"~24") PN10
DN50~DN600(2"~24") PN16
DN50~DN200(2"~8") PN25 |
| Nominal pressure | 0.1MPa-0.8MPa
0.8MPa-1.3MPa
1.3MPa-2.0MPa |
| Operating temperature | 0°C~85°C |
| Seal test | 1.1PN |
| Shell test | 1.5PN |
| Suitable medium | Water |
The adjustable pressure-reducing valve is a pilot pressure-reducing valve, which is composed of the main valve of the hydraulic control valve and the pressure-reducing pilot valve.The main valve outlet pressure change through the pilot valve amplification control of the main valve disc action;The work of the reduced pressure pilot valve is based on the balance between the force exerted by the spring downward to open the disc and the force exerted by the diaphragm upward to close the disc.When water is used at the back end of the main valve, the pressure of the guide valve spring is greater than the pressure acting on the lower end of the dowm.Guide valve open, the main valve cavity drain to the outside, the main valve open;When water is not used at the back end of the main valve, the back end pressure increases.Push the guide valve diaphragm upward to close the guide valve, thus closing the main valve and stabilizing the pressure at the back end at the set value;The water consumption of the back end of the main valve is different, so that the water pressure acting on the lower end of the diaphragm of the pilot valve is different.The opening of the pilot valve changes accordingly.In order to control the size of the main valve opening, so that the pressure at the back end is always kept at the set value;The pressure value set at the back of the valve can be adjusted by the adjusting screw on the pressure relief guide valve.2.Factory tour
3.FAQQ1.How about your delivery time?
A. Commonly, it is 5-10 days if in enough stock. It will takes about 20-30 days after receiving the deposit, the delivery time depends on the items and the order quantity.
Q2: Are you trading company or manufacturer ?
A: We are a manufacturer of hydraulic control valve,gate valve,butterfly valve,check valve,pressure reducing valve and other valve parts for Water plant, secondary water supply, municipal pipe network, reservoir, garbage treatment plant, subway and other industries in municipal engineering;Petrochemical, steel plant, power plant, shipbuilding and paper-making, bio-pharmaceutical, etc
Q3: Can you produce according to our own drawings?
A: Yes, please send your own drawing draft to us.OEM items are welcome.
Q4: Do you provide samples ? is it free or extra ?
A: Yes, we'd like to offer the sample for free charge but the freight will be on your charge.
Q5: Do you have agent or representative abroad?
A: We don't have any agents abroad up to now. If you have interests to join us as agent and enjoy more discounts.Just feel free to contact us then we can discuss more details.
Q6: Can we print the LOGO on products?
A: Yes, the OEM is available with the permission of our customers.
Q7. what is your payment term?
A: T/T or L/C,if you want any other way,please contact us.
Q8: what is your main market?
A:Eastern Europe, Southeast Asia, Africa, Oceania, Mid East, Eastern Asia, Western Europe, North America, South America, and so on.
Q9: If products have some quality problem, how will you deal with?
A: We will be responsible for all the quality problems.
Q10: What can I get from cooperating with SUOTE VALVE?
A: 1. Special valves, with customized service.
2. Timely production and delivery, time is money.
3. Market protection service, long term business strategy.
More info pls just feel free to contact:Shanghai Suote Valve Co., Ltd.
Basic Information
-
Year Established
--
-
Business Type
--
-
Country / Region
--
-
Main Industry
--
-
Main Products
--
-
Enterprise Legal Person
--
-
Total Employees
--
-
Annual Output Value
--
-
Export Market
--
-
Cooperated Customers
--
